Important points you need to confirm before configuring your Brother machine for a wireless network.
Check the following points before you connect your Brother machine to your wireless network.
Configuring the Brother machine for a wireless network using Wi-Fi Protected Setup or AOSS™.
Configuring the Brother machine manually for a wireless network.
Function settings of your WLAN access point
- IP address allocation
If your WLAN access point/router supports either Wi-Fi Protected Setup or AOSS™, you can easily connect your Brother machine to your wireless network without a computer. To confirm if your WLAN access point/router support the WPS or AOSS™, check if the WLAN access point/router has the WPS or AOSS™ symbol as shown below.
Before configuring wireless settings, you will need to know your Network name: (SSID, ESSID) and Network Key.
Do one of the following to find the Network Name (SSID, ESSID) and Network Key:
See the side of your WLAN access point/router.
NOTE: The illustration shown below may differ depending on the product being used.
- See the documentation provided with your WLAN access point/router.
- The initial Network Name could be the manufacturer's name or the model name.
- If you still cannot find the security information, consult the manufacturer of your WLAN access point/router, your system administrator or internet provider.
WPA-PSK/WPA2-PSK is one of the network authentication methods which use a Pre-Shared Key (PSK) that is 8 or more characters in length, up to a maximum of 63 characters.
Depending on the WLAN access point being used, some functions of WLAN access point/router may cause interference to wireless communication between your computer and the Brother machine. See the instructions supplied with your WLAN access point/router and confirm your function settings. If the following functions are enabled, change the setting.
This function allows you to configure multiple SSIDs with one WLAN access point/router. Each SSID can use different authentication and encryption methods so that you can connect wireless devices to the wireless network at different security levels at the same time. However, if you want to connect all wireless devices to a specific wireless network, these devices have to use the same SSID. In many cases, devices using different SSID cannot communicate with each other, and cannot send or receive data through the same wireless network. Configure your wireless computer and Brother machine with the same SSID as used for your WLAN access point/router.
NOTE: The illustration shown below may differ depending on the product being used and the encryption methods are one example.
Privacy Separator isolates all wireless devices connected to your WLAN access point/router, and prevents the wireless devices from being able to connect and send data to other devices in your wireless network.
When Privacy Separator is on, wireless devices such as your computer and your Brother machine will not be able to communicate with each other. To connect your Brother machine to the other devices, change the setting of your WLAN access point/router and disable Privacy Separator.
MAC address filtering
MAC address filtering is a function that allows only specific MAC address configured in the WLAN access point/ router to connect. If you are using MAC address filtering in the WLAN access point/ router, you need to configure your MAC address of your Brother machine.
You can find your machine's MAC Address by printing the Network Configuration List.
> Click here to see the details of how to print the Network Configuration List.
Assigning Static IP addresses
Before you assign the IP address manually using Static mode, read the following.
The IP address which you wish to assign to your Brother Machine:
- Must be selected from outside the range of the IP address that might be assigned as a dynamic address by DHCP server.
- Must be different from the one that has been already assigned to another device in your network.
- Must be on the same network as your computer and the WLAN access point/router.
If the IP address assigned to your computer is 192.168.1.xx, assign any number which has not assigned to other devices to where xx is (e.g. 192.168.1.10). The first three series of numbers (192.168.1 as shown in the example) must be the same.
Assigning IP address automatically
If your WLAN access point/router does not support a DHCP server function, the IP address can not be automatically configured. For more information, see the documentation supplied with your WLAN access point/router.
DCP-1610W, DCP-1615NW, DCP-1616NW, DCP-9015CDW, DCP-J105, DCP-J140W, DCP-J152W, DCP-J172W, DCP-J315W, DCP-J4110DW, DCP-J4120DW, DCP-J515W, DCP-J525W, DCP-J552DW, DCP-J715W, DCP-J725DW, DCP-J752DW, DCP-J925DW, DCP-L2540DW, DCP-L2541DW, DCP-T500W, DCP-T700W, HL-1210W, HL-1211W, HL-2135W, HL-2270DW, HL-3075CW, HL-3170CDW, HL-4570CDW, HL-5470DW, HL-6180DW, HL-L2305W, HL-L2340DW, HL-L2365DW, HL-L2366DW, HL-L2380DW, HL-L8350CDW, HL-L9200CDW, MFC-1910W, MFC-1911NW, MFC-1911W, MFC-1915W, MFC-1916NW, MFC-7860DW, MFC-8910DW, MFC-8950DW, MFC-9325CW, MFC-9330CDW, MFC-9335CDW, MFC-9340CDW, MFC-9970CDW, MFC-J200, MFC-J2310, MFC-J2320, MFC-J2510, MFC-J265W, MFC-J2720, MFC-J3520, MFC-J3720, MFC-J415W, MFC-J430W, MFC-J432W, MFC-J4410DW, MFC-J4510DW, MFC-J4620DW, MFC-J470DW, MFC-J4710DW, MFC-J475DW, MFC-J5320DW, MFC-J5720DW, MFC-J5910DW, MFC-J5920DW, MFC-J615W, MFC-J625DW, MFC-J650DW, MFC-J6510DW, MFC-J6520DW, MFC-J6710DW, MFC-J6720DW, MFC-J6910DW, MFC-J6920DW, MFC-J825DW, MFC-J870DW, MFC-L2700DW, MFC-L2701DW, MFC-L2703DW, MFC-L2720DW, MFC-L2740DW, MFC-L8600CDW, MFC-L8850CDW, MFC-L9550CDW, MFC-T800W