PE-DESIGN Ver.7

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 24/01/2014
  • ID: faqh00000101_002

When I sew an embroidery pattern design exported as DST format in PE-DESIGN, how do I specify whether or not the jump stitches are cut on the embroidery machine of the PR series?

Check the value in the Number of jumps for trim box when the embroidery pattern design is exported as DST format in PE-DESIGN, and then check the specified number of jump codes on the embroidery machine of the PR series.

navi How to find the numerical values on each of the settings screens

navi When not cutting the upper and bobbin thread before the jump stitch

navi When cutting the upper and bobbin thread before the jump stitch

 

  • How to find the numerical values on each of the settings screens
    • Check the numerical value in the Number of jumps for trim box when the embroidery pattern design is exported as DST format in PE-DESIGN.

      Check the numerical value in the Number of jumps for trim box when the embroidery pattern design is exported as the DST format in PE-DESIGN.
       
    • Check the numerical value in the number of jump codes on the embroidery machine of the PR series.

      Check the numerical value in the number of jump codes on the embroidery machine of the PR series.
       

A value between 1 and 8 can be specified.

 

top top

 

 

  • When not cutting the upper and bobbin thread before the jump stitch

    The thread trimming and "DST" setting can be specified from the second page of the settings screen on the embroidery machine of the PR series.
    Touch "ON" key (or "OFF" key) and select the desired setting.
    In either of the following cases, it will not be cut the upper and bobbin thread before the jump stitch.
    • Select "OFF" and the key appears as "OFF" key.

      Select "OFF".
       
    • Select "ON" and the key appears as "ON" key.

      Select "ON" .

      Change the following numerical values on each of the settings screens.
      Select the appropriate value, making sure that it meets the following conditions.
      The numerical value in the Number of jumps for trim box when the embroidery pattern design is exported as the DST format in PE-DESIGN greater than character The numerical value in the number of jump codes on the embroidery machine of the PR series

      For example, if the Number of jumps for trim box in PE-DESIGN is set to "7" and the number of jump codes on the embroidery machine is set to "8", it will not be cut the upper and bobbin thread before the jump stitch.

       

top top

 

 

  • When cutting the upper and bobbin thread before the jump stitch

    The thread trimming and "DST" setting can be specified from the second page of the settings screen on the embroidery machine of the PR series.
    Select "ON" and the key appears as "ON" key.

    Select "ON" .

    Change the following numerical values on each of the settings screens.
    Select the appropriate value, making sure that it meets the following conditions.
    The numerical value in the Number of jumps for trim box when the embroidery pattern design is exported as the DST format in PE-DESIGN more than The numerical value in the number of jump codes on the embroidery machine of the PR series

    For example, if the Number of jumps for trim box in PE-DESIGN is set to "8" and the number of jump codes on the embroidery machine is set to "8", it will be cut the upper and bobbin thread before the jump stitch.

     
 

Related FAQs

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

PE-DESIGN 8, PE-DESIGN Ver.7, PR-600/600C, PR-620/620C/600II/600IIC

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit