Printer Driver Installation

With a USB connection
With a Serial connection

*****************************************************************

With a USB connection
------------------------------------------------------------------

 Printer Driver Installation
 (With a USB connection)

  Copyright (C) Brother Industries, Ltd.

------------------------------------------------------------------

******************************************************************

Note:
* Before starting the installation, make sure that the STAMPCREATOR
  is not connected to the computer.
* Be sure to carefully read the installation procedure described
  below, and connect the machine when you are instructed to do so.
  In addition, quit all other applications before starting the
  installation.

* Place the downloaded file in any folder, such as [C:\WORK],
  decompress it, and then start it up. If this operation is
  performed from the desktop, it may not start up correctly.
* Follow the procedure below when connecting the STAMPCREATOR to
  a computer using a USB cable.
  In addition, a USB cable cannot be used to connect a computer
  running Windows 95 or Windows NT 4.0.

******************************************************************

1. Make sure that the STAMPCREATOR is not connected to the computer.
2. Start up [D_SETUP.EXE] in the folder that was decompressed.
3. In the dialogue box that appears, allowing the type of
   connection to be chosen, select [USB cable], and then click
   the OK button.
   If the STAMPCREATOR printer driver has already been installed,
   continue with step 4.
   If the printer driver is being installed for the first time,
   skip to step 9.
4. If a message appears, stating that an old driver has been
   detected, click the OK button to close the message.
5. The Driver Setup (Brother (STAMPCREATOR)) dialogue box that
   appears allows you to select whether to replace, add or delete
   the printer driver.
   (If the choices are not available, skip to step 9.)
   If the choices are available, select [Delete Brother
   (STAMPCREATOR)], and then click the Next button.
6. In the dialogue box that appears, asking for confirmation to
   delete the printer driver, click the Yes button.
7. After the printer driver is deleted, a dialogue box containing
   the message [Brother (STAMPCREATOR) was correctly deleted.]
   appears. If a dialogue box appears, explaining that the computer
   should be restarted,  select [Yes, restart immediately.],
   and then click the Finish button.
   The computer is restarted.
   If you are not prompted to restart the computer, click the
   Finish button, and then restart the computer.
8. After the computer is restarted, start up [D_SETUP.EXE]
   in the folder that was decompressed.
   In the dialogue box that appears, allowing the type of
   connection to be chosen, select [USB cable], and then click
   the OK button.
9. In the Driver Setup (Brother (STAMPCREATOR)) dialogue box that 
   appears, click the Next button.
10. A dialogue box containing the message [Preparing for setup...]
    appears, and then the message [Preparation for setup is
    finished.] appears.
    Connect the STAMPCREATOR to the computer, and then turn it on.
11 .The driver for the STAMPCREATOR is automatically installed.
     In the dialogue box that appears, containing the message
    [Brother (STAMPCREATOR) was correctly added.], click the Finish
    button.
    This completes the installation.
    If the Add Printer Wizard started up without the STAMPCREATOR
    driver automatically being installed
    (with Windows 98SE/Me), click the Cancel button to close
    the Add Printer Wizard.
    Then, click the Finish button in the Driver Setup
    (Brother (STAMPCREATOR)) dialogue box, and restart the computer.
    Afterwards, repeat the procedure from step 8.
 

******************************************************************

With a Serial connection
--------------------------------------------------------------------------

 Printer Driver Installation
 (With a serial connection)

  Copyright (C) Brother Industries, Ltd.

--------------------------------------------------------------------------

****************************************************************************

Note:
* Follow the procedure below when connecting the STAMPCREATOR to
  a computer using a serial cable.

* Place the downloaded file in any folder, such as [C:\WORK],
  decompress it, and then start it up.
  If this operation is performed from the desktop, it may
  not start up correctly.

****************************************************************************

1. Connect the STAMPCREATOR to the computer, and then turn on both
   machines.
2. Start up [D_SETUP.EXE] in the folder that was decompressed.
3. In the dialog box that appears, allowing the type of
   connection to be chosen, select [Serial cable], and then click
   the OK button.
4. In the first Installer dialog box, make sure that [Install]
   is selected, and then click the Next button.
5. The next dialog box that appears allows you to select the
   port where the printer is connected. 
   Select [COM1:] if the STAMPCREATOR is connected to the COM1 port,
   or select [COM2:] if it is connected to the COM2 port,
   and then click the Next button.
6. In the dialog box that appears, asking for confirmation on
   how the installation will be carried out,
    click the Next button if the displayed settings are correct.
7. The printer driver is installed.
8. In the final dialog box that appears, click the Finish button,
   and then restart the computer.